DCS Caucasus Mission Planning Guide

Click the map to drop waypoints
Mission date

Airfields 21

ICAOTowerTACANILS
UGSB136,791 ft33 ft
UG5X077,408 ft59 ft
UGKS097,257 ft43 ft
UGKO077,936 ft148 ft
UGTB13 · 317,694 ft1,565 ft
UGSG13 · 317,844 ft1,526 ft
UG24--7,871 ft1,483 ft
UGSS--11,217 ft66 ft
UG23--7,841 ft33 ft
URSS-069,685 ft98 ft
URKG--5,453 ft72 ft
URKA--8,625 ft141 ft
URKW--6,732 ft66 ft
URKN--5,640 ft131 ft
URKL--7,661 ft98 ft
URKK--9,738 ft112 ft
URKM--10,197 ft591 ft
URMM-12 · 3012,316 ft1,050 ft
URMN-246,719 ft1,398 ft
URMO-109,327 ft1,739 ft
XRMF--7,733 ft509 ft

The DCS World Caucasus map is a Black Sea theater: Georgian and Russian airfields, a coast on the water, and alpine ground inland toward Mt Elbrus. DCS Planner loads that theater with the same airfield and frequency catalog the map uses, so you can build the route before you spawn.

This page is the Caucasus theater detail for the step-by-step DCS mission planning workflow.

Caucasus theater overview

Black Sea region - Georgia/Russia. The playable terrain is about 448 NM east-west and 240 NM north-south. A hop along the Black Sea coast is a short fighter leg. A transit from Batumi inland to Tbilisi or Beslan is not. Plan fuel and time-on-target against those distances.

The catalog on this theater covers runway airfields in Georgia and Russia, including the Sukhumi coast and the North Caucasus basin. The Black Sea is open water for tanker and AWACS tracks. For the eastern Mediterranean theater, see the DCS Syria Mission Planning Guide. For the Strait of Hormuz, see the DCS Persian Gulf Mission Planning Guide.

Elevation in the planner's Caucasus terrain runs from 0 m (0 ft) up to 5640 m (18504 ft): sea level on the Black Sea, then alpine ground toward Mt Elbrus. DCS treats local time here as UTC+4.

DCS Planner currently lists 21 runway airfields on Caucasus. Country outlines appear on the map tiles. The sim does not enforce real-world FIR or ADIZ rules unless the mission designer adds them. Coalition is blue, red, or neutral. Plan the route against the brief, the IADS the mission places, and the terrain, not as if national borders are simulated.

Key airfields, ATC and TACAN frequencies

Click an airfield on the Caucasus map for tower, ground, TACAN, and VOR when that data exists. The table below is the same catalog: runway fields by region. Empty TACAN cells mean the catalog has no TACAN on that airfield, not that DCS has none in every mission. TACAN in this catalog currently sits on 6 of those fields.

Tower and TACAN from the DCS Planner Caucasus airfield catalog. Values change when the catalog is rebuilt from DCS.
RegionAirfieldICAOTowerTACAN
West GeorgiaBatumiUGSB131.0016X
West GeorgiaKobuletiUG5X133.0067X
West GeorgiaSenaki-KolkhiUGKS132.0031X
West GeorgiaKutaisi-KopitnariUGKO134.0044X
Tbilisi areaTbilisi-LochiniUGTB138.0025X
Tbilisi areaVazianiUGSG140.0022X
Tbilisi areaSoganlugUG24139.00-
Sukhumi coastSukhumi-BabusharaUGSS129.00-
Sukhumi coastGudautaUG23130.00-
Russia Black SeaSochi-AdlerURSS127.00-
Russia Black SeaGelendzhikURKG126.00-
Russia Black SeaAnapa-VityazevoURKA121.00-
Russia Black SeaKrymskURKW124.00-
Russia Black SeaNovorossiyskURKN123.00-
KrasnodarKrasnodar-CenterURKL122.00-
KrasnodarKrasnodar-PashkovskyURKK128.00-
KrasnodarMaykop-KhanskayaURKM125.00-
North CaucasusMineralnye VodyURMM135.00-
North CaucasusNalchikURMN136.00-
North CaucasusBeslanURMO141.00-
North CaucasusMozdokXRMF137.00-

Turn on the Nav Beacons layer for TACAN, VOR, and similar stations from the DCS terrain data. Put those frequencies on the kneeboard if you want them in the cockpit without leaving the jet.

Bullseye and navigation on Caucasus

Bullseye is a shared coalition reference, not a waypoint on the route. Put it where the package will fight or talk, not in a distant corner of the map. A call of bearing and range from that point should still be useful when flights are on the Black Sea coast and others are inland at Tbilisi or Beslan.

Import a .miz to load the mission bullseye, or right-click the map and choose Set bullseye here. See DCS Bullseye Explained (BRAA vs Bullseye) for how to read a call and how the planner draws the rings.

Click the map to drop waypoints. Each leg shows distance in nautical miles and a heading marked T (true) or M (magnetic once the mission has a date). Magnetic variation is not the same across this theater, so set the mission date before you copy a leg heading into a compass or HSI. See DCS Flight Plan: Waypoints, Headings & Routes for coordinate formats and airframe waypoint limits.

Straight-line examples from the catalog, true heading:

  • Batumi to Sochi-Adler: 132.4 NM, 327°T
  • Kutaisi-Kopitnari to Tbilisi-Lochini: 114.7 NM, 105°T
  • Batumi to Vaziani: 153.8 NM, 088°T
  • Beslan to Tbilisi-Lochini: 93.7 NM, 170°T

Terrain and safe altitudes

Low-level work over the Black Sea is a different problem from a night transit toward Mt Elbrus or a hop through the Tbilisi basin. After the route exists, DCS Planner samples terrain along it: AGL clearance, a terrain profile, MSA, and peak markers. Raise the altitude or move the waypoint if a ridge sits on the nose.

Peak markers are on by default. Use them before you commit to a low ingress inland. The 3D radar view shows terrain masking against SAM radar. The planner does not compute bingo fuel; check fuel in the cockpit and with the loadout builder.

Typical threats and where they sit

Threats are whatever the mission places. Caucasus does not ship a fixed IADS. Community and campaign missions often put layered air defences around defended airfields and along the likely ingress from the coast into the mountains. That is a mission-design habit, not a map default.

In DCS Planner, place SAM and AAA units on the Caucasus map. Launchers show threat rings that use DCS engagement ranges. Draw ingress outside rings you cannot defeat, and use terrain later to hide from radar you cannot avoid. The SAM encyclopedia has detection, tracking, and launch ranges for systems the planner knows. See DCS SAM Threat Rings & Route Planning for engagement range vs NEZ and how to draw ingress around the rings.

Plan a Caucasus mission in the browser

Open DCS Planner and pick the Caucasus theater. Then:

  1. Open DCS Planner and select Caucasus. The planner default is Persian Gulf if no other map is stored, so switch the theater before you click the route.
  2. Click an airfield on the map, or use the catalog table on this page, for tower and TACAN when that data exists.
  3. Start the route at a Georgian or Russian catalog field. Use the Black Sea for tanker or AWACS tracks when the brief needs water.
  4. Put bullseye where the package will talk, often the Black Sea coast or the Tbilisi basin, not in a distant corner of the map.
  5. Drop waypoints and check heading and distance on each leg before you commit fuel or time-on-target. Headings read M (magnetic) once the mission has a date, T (true) otherwise.
  6. Add the threats from the brief. Launchers show DCS engagement ranges. Draw ingress outside rings you cannot defeat.
  7. Read AGL clearance, MSA, and the terrain profile, especially on legs that leave the coast toward the alpine ridge.
  8. Export a kneeboard PNG, a .miz with units, drawings, and bullseye, DCS-DTC JSON, or a native .DTC for airframes that support it.

Import works for .miz, .trk, and CombatFlite .cf, so you can open an existing Caucasus mission and edit the route inline. The core planner is free and does not require a login.

Open the planner

FAQ

What area does the DCS Caucasus map cover?
The theater is the Black Sea region: Georgia and Russia, with a coast on the water and alpine ground inland toward Mt Elbrus. In DCS Planner it spans about 448 NM east-west and 240 NM north-south.
Where do I find Caucasus airfield frequencies?
DCS Planner shows tower, ground, TACAN, and VOR on an airfield when that data exists in the catalog. Click an airfield on the Caucasus map. This page lists tower and TACAN for the catalog runway fields.
Which Caucasus airfields have TACAN in DCS Planner?
The catalog currently lists TACAN on 6 Caucasus airfields: Batumi, Kobuleti, Senaki-Kolkhi, Kutaisi-Kopitnari, Tbilisi-Lochini, and Vaziani. Empty TACAN cells on the other fields mean the catalog has no TACAN there, not that a mission cannot add one.
How do I plan a Caucasus mission in DCS Planner?
Open the planner, pick the Caucasus theater, set bullseye, click the route, place SAM or AAA rings, check AGL and MSA along the legs, then export a kneeboard PNG, a .miz, or a DTC.
Does DCS enforce national airspace on the Caucasus map?
No. The map includes Georgia and Russia, but DCS does not apply real-world FIR or ADIZ rules unless the mission designer adds them. Plan against coalition IADS, terrain, and the brief, not as if national borders are simulated. The catalog currently lists 21 runway airfields on this theater.